Low temperature atomic layer deposition of cobalt using dicobalt hexacarbonyl-1-heptyne as precursor

• Mathias Franz,
• Mahnaz Safian Jouzdani,
• Lysann Kaßner,
• Marcus Daniel,
• Frank Stahr and
• Stefan E. Schulz

Beilstein J. Nanotechnol. 2023, 14, 951–963, doi:10.3762/bjnano.14.78

• temperature where the cobalt precursor does not decompose. In that way, the upper limit of a possible ALD window can be approximated. The CVD experiments of Melzer et al. [32] demonstrated a precursor reaction with O2 in the temperature region from 130 to 250 °C to form cobalt oxide. The deposition

• Abbe parameter of 0.41, indicating a significant systematic error (see Supporting Information File 1, Figure S2). It is therefore reasonable to assume at least two oxygen components. One is located at 531.9 eV correlated to oxygen in cobalt oxide [36][37]. The higher bonding energy at 532.5 eV

Evaluation of electrosynthesized reduced graphene oxide–Ni/Fe/Co-based (oxy)hydroxide catalysts towards the oxygen evolution reaction

• Karolina Cysewska,
• Marcin Łapiński,
• Marcin Zając,
• Jakub Karczewski,
• Piotr Jasiński and
• Sebastian Molin

Beilstein J. Nanotechnol. 2023, 14, 420–433, doi:10.3762/bjnano.14.34

• 260 mV (Tafel slope: 72 mV·dec−1) and 320 mV (65 mV∙dec−1) determined at 10 mA·cm−2 in 1 M potassium hydroxide (KOH), respectively. In another work, nickel/nickel oxide (Ni-NiO) and cobalt/cobalt oxide (Co-CoO) were chemically synthesized with three-dimensional hierarchical porous graphene (3DHPG) on

Structural studies and selected physical investigations of LiCoO₂ obtained by combustion synthesis

• Monika Michalska,
• Paweł Ławniczak,
• Tomasz Strachowski,
• Adam Ostrowski and
• Waldemar Bednarski

Beilstein J. Nanotechnol. 2022, 13, 1473–1482, doi:10.3762/bjnano.13.121

• the annealing temperature causes a steady decrease in the DC conductivity. Keywords: lithium cobalt oxide; lithium-ion battery; nanocrystalline powder; solution combustion synthesis; Introduction Lithium cobalt oxide (LiCoO2, LCO) of hexagonal structure () was first used as cathode material in

• capable of reversibly intercalating lithium ions [2]. The commercialization of lithium-ion cells was achieved in the early 1990s by Sony Corporation and in 1992 by a joint venture company (Asahi Kasai and Toshiba) [2][3][4]. Almost 90% of commercial Li-ion batteries consist of a lithium cobalt oxide

• is a widely used method for the creation of nanomaterials [48][49][50][51][52][53][54][55][56][57]. Acetates, carbonates, and nitrate salts of lithium and cobalt are often utilized as starting materials and oxidizers in the combustion synthesis of lithium cobalt oxide [50][58][59]. Different ammonium

Electrocatalytic oxygen reduction activity of AgCoCu oxides on reduced graphene oxide in alkaline media

• Iyyappan Madakannu,
• Indrajit Patil,
• Bhalchandra Kakade and
• Kasibhatta Kumara Ramanatha Datta

Beilstein J. Nanotechnol. 2022, 13, 1020–1029, doi:10.3762/bjnano.13.89

• the oxygen reduction reaction (ORR) in alkaline medium. Varying the Ag fraction in copper cobalt oxide has a significant influence on the ORR activity. At a ratio of 2:1:1, AgCuCo oxide NPs on rGO displayed the best values for onset potential, half-wave potential, and limiting current density (Jk) of

• 0.94 V vs RHE, 0.78 V, and 3.6 mA·cm−2, respectively, with an electrochemical active surface area of 66.92 m2·g−1 and a mass activity of 40.55 mA·mg−1. The optimum electrocatalyst shows considerable electrochemical stability over 10,000 cycles in 0.1 M KOH solution. Keywords: copper cobalt oxide NPs

The effect of cobalt on morphology, structure, and ORR activity of electrospun carbon fibre mats in aqueous alkaline environments

• Markus Gehring,
• Tobias Kutsch,
• Osmane Camara,
• Alexandre Merlen,
• Hermann Tempel,
• Hans Kungl and
• Rüdiger-A. Eichel

Beilstein J. Nanotechnol. 2021, 12, 1173–1186, doi:10.3762/bjnano.12.87

• three main groups: electroplating, electroless plating, and bottom-up methods such as vapour deposition. Another way to introduce metals to a carbon fibre system in form of nanoparticles was reported by groups who prepared cobalt/cobalt oxide-decorated carbon nanofibres from electrospinning by adding a

• fibres. Alegre et al. [21][22] also investigated cobalt-oxide-enhanced fibres, unlike Song et al. they focussed on an alkaline aqueous system. They performed polarisation experiments using their Co3O4-enhanced fibres as catalytically active component in a pressed carbon electrode in 6 M KOH and found it

• temperatures, the amount of the presumed hydroxide decreases, mainly in favour of metallic cobalt and, in parts, cobalt oxide(s). As a general trend, this effect is stronger, when the carbonisation temperatures are higher. The signal intensity of the shoulder of the main Co(0) peak, visible for the sample

Molecular assemblies on surfaces: towards physical and electronic decoupling of organic molecules

• Sabine Maier and
• Meike Stöhr

Beilstein J. Nanotechnol. 2021, 12, 950–956, doi:10.3762/bjnano.12.71

• these aspects for the self-assembly of porphyrin derivatives on cobalt oxide films on top of Ir(100). While the unfunctionalized diphenylporphyrin self-assembled on the bilayer film but not on the two-bilayer film, the opposite observation was made for cyanotetraphenylporphyrin. Physical decoupling of

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• obtained material was composed of loosely arranged nanoparticles whose average diameter was about 36 nm. The as-prepared cobalt oxide powder was also tested as the anode material for Li-ion batteries and revealed specific capacities of 1060 and 533 mAh·g−1 after 100 cycles at charge–discharge current

• current densities between 50 and 5000 mA·g−1. Keywords: anode material; cobalt oxide; lithium-ion battery; solution combustion synthesis; transition metal oxide; Introduction Recently, a considerable research effort regarding new anode materials has been made because the traditional carbonaceous anodes

• is also important to mention that no impurities have been detected using XRD and RS. This confirms the successful formation of the Co3O4 material which, in addition, is highly pure and well crystalline. The morphology of the investigated cobalt oxide has been determined with SEM and TEM (Figure 2

Exploring the fabrication and transfer mechanism of metallic nanostructures on carbon nanomembranes via focused electron beam induced processing

• Christian Preischl,
• Linh Hoang Le,
• Elif Bilgilisoy,
• Armin Gölzhäuser and
• Hubertus Marbach

Beilstein J. Nanotechnol. 2021, 12, 319–329, doi:10.3762/bjnano.12.26

• beam-induced surface activation (EBISA) are studied with the precursors Fe(CO)5 and Co(CO)3NO on SAMs of 1,1′,4′,1′′-terphenyl-4-thiol (TPT). For Co(CO)3NO only EBID leads to deposits consisting of cobalt oxide. In the case of Fe(CO)5 EBID and EBISA yield deposits consisting of iron nanocrystals with

• without any changes, aside from oxidation. Here we demonstrate that iron as well as cobalt oxide structures on top of a cross-linked SAM on Ag/mica do change more significantly. The Fe(NO3)3 solution used for etching of the Ag layer also dissolves the cobalt oxide structures and causes dissolution and

• fabricated on the same substrate exhibits a height of 60 nm (Figure S8, Supporting Information File 1). The resulting deposit consists of small cobalt oxide particles, interpreted on the basis of the corresponding blowup image (Figure 6a) and the local AE spectrum (Figure 6e). Only minor impurities of carbon

Adsorption and self-assembly of porphyrins on ultrathin CoO films on Ir(100)

• Feifei Xiang,
• Tobias Schmitt,
• Marco Raschmann and
• M. Alexander Schneider

Beilstein J. Nanotechnol. 2020, 11, 1516–1524, doi:10.3762/bjnano.11.134

• surfaces is of fundamental interest due to a variety of potential applications. We investigate here the molecule–molecule and molecule–substrate interaction of Co-5,15-diphenylporphyrin (Co-DPP) and 2H-tetrakis(p-cyanophenyl)porphyrin (2H-TCNP) on one bilayer (1BL) and two bilayer (2BL) thick cobalt oxide

• islands on the 2BL film. The findings demonstrate the guiding effect of the cobalt oxide films of different thickness and the effect of functional surface anchoring. Keywords: adsorption energy; molecular rotors; porphyrins; self-assembly; transition metal oxides; Introduction Due to their variability

• atomic structure of these films has been investigated in detail by diffraction methods [18][19][20][21]. The corresponding data ensures reproducibility of the cobalt oxide preparation and meaningful computer-based substrate modeling. Functionalization of porphyrins may introduce new properties of the

Comparison of fresh and aged lithium iron phosphate cathodes using a tailored electrochemical strain microscopy technique

• Matthias Simolka,
• Hanno Kaess and
• Kaspar Andreas Friedrich

Beilstein J. Nanotechnol. 2020, 11, 583–596, doi:10.3762/bjnano.11.46

• [29][30] and nickel manganese cobalt oxide (NMC) [42][43] but, to the best of our knowledge, not for LFP. In this paper, we analyse the electrochemical activity and Li-ion concentration using the ESM technique and show a decrease of the electrochemical activity and a reduced active Li content in the

Multilayer capsules made of weak polyelectrolytes: a review on the preparation, functionalization and applications in drug delivery

• Varsha Sharma and
• Anandhakumar Sundaramurthy

Beilstein J. Nanotechnol. 2020, 11, 508–532, doi:10.3762/bjnano.11.41

• of magnetic NPs (e.g., iron oxide and cobalt oxide NPs) into capsules allows them to respond to magnetic stimuli and produce heat due to magnetic energy dissipation, mechanical vibrations and motion induced in the film, thus releasing the cargo [80]. The Fe2O4-PAH capsules studied with A549 cancer

Ultrathin Ni_1−xCo_xS₂ nanoflakes as high energy density electrode materials for asymmetric supercapacitors

• Xiaoxiang Wang,
• Teng Wang,
• Rusen Zhou,
• Lijuan Fan,
• Shengli Zhang,
• Feng Yu,
• Tuquabo Tesfamichael,
• Liwei Su and
• Hongxia Wang

Beilstein J. Nanotechnol. 2019, 10, 2207–2216, doi:10.3762/bjnano.10.213

• F·g−1 at 1 A·g−1 were synthesized by Zhang and Lou [17]. Ni–Co mixed oxide nanoprisms with a capacitance of 1000 F·g−1 at 10 A·g−1 were also reported by Yu and co-workers [18]. Differently designed nanostructures will impact the electrochemical performance of nickel–cobalt oxide/sulfide materials

Materials nanoarchitectonics at two-dimensional liquid interfaces

• Katsuhiko Ariga,
• Michio Matsumoto,
• Taizo Mori and
• Lok Kumar Shrestha

Beilstein J. Nanotechnol. 2019, 10, 1559–1587, doi:10.3762/bjnano.10.153

• reported. Jayavel, Shrestha, and co-workers demonstrated the enhanced performance of electrochemical supercapacitors using composites of cobalt oxide nanoparticles and reduced graphene oxide, which are zero-dimensional and two-dimensional nanomaterials, respectively [86]. Leong and co-workers reported a

Renewable energy conversion using nano- and microstructured materials

• Harry Mönig and
• Martina Schmid

Beilstein J. Nanotechnol. 2019, 10, 771–773, doi:10.3762/bjnano.10.76

• in nanoporous cobalt oxide photocathodes [7], and an approach in which silicon nanoparticles are embedded in an amorphous carbon matrix [8]. In terms of material saving, nano- and microstructured absorbers offer great potential, e.g., via ultrathin absorbers as highlighted for Sb2S3 hybrid solar

Graphene-enhanced metal oxide gas sensors at room temperature: a review

• Dongjin Sun,
• Yifan Luo,
• Marc Debliquy and
• Chao Zhang

Beilstein J. Nanotechnol. 2018, 9, 2832–2844, doi:10.3762/bjnano.9.264

• achieved at all [19][20]. Metal-oxide semiconductors (MOS), including tin oxide (SnO2), titanium dioxide (TiO2), zinc oxide (ZnO), copper oxide (CuO), tungsten oxide (WO3), indium oxide (In2O3), ferric oxide (Fe2O3) and cobalt oxide (Co3O4) are important materials for gas sensors [21][22][23][24][25][26

Hydrothermal-derived carbon as a stabilizing matrix for improved cycling performance of silicon-based anodes for lithium-ion full cells

• Mirco Ruttert,
• Florian Holtstiege,
• Jessica Hüsker,
• Markus Börner,
• Martin Winter and
• Tobias Placke

Beilstein J. Nanotechnol. 2018, 9, 2381–2395, doi:10.3762/bjnano.9.223

• containing the synthesized materials were used as working electrodes (WE), while lithium metal (Li; Albemarle Corporation) was used as counter and reference (RE) electrodes. In the full cell set-up, the Si/C composite electrodes were cycled vs lithium nickel manganese cobalt oxide (LiNi1/3Mn1/3Co1/3O2, NMC

A review of carbon-based and non-carbon-based catalyst supports for the selective catalytic reduction of nitric oxide

• Shahreen Binti Izwan Anthonysamy,
• Syahidah Binti Afandi,
• Mehrnoush Khavarian and
• Abdul Rahman Bin Mohamed

Beilstein J. Nanotechnol. 2018, 9, 740–761, doi:10.3762/bjnano.9.68

Near-infrared-responsive, superparamagnetic Au@Co nanochains

• Varadee Vittur,
• Arati G. Kolhatkar,
• Shreya Shah,
• Irene Rusakova,
• Dmitri Litvinov and
• T. Randall Lee

Beilstein J. Nanotechnol. 2017, 8, 1680–1687, doi:10.3762/bjnano.8.168

• to Au 4f electrons, as well as peaks at 780.2 and 795.3 eV, which can be attributed to Co 2p electrons. The minor broadened peaks that were observed at binding energies of ca. 790 eV and just above 800 eV can be attributed to cobalt oxide [37]. Since XPS is a surface technique, the penetration depth

Synthesis of graphene–transition metal oxide hybrid nanoparticles and their application in various fields

• Arpita Jana,
• Elke Scheer and
• Sebastian Polarz

Beilstein J. Nanotechnol. 2017, 8, 688–714, doi:10.3762/bjnano.8.74

• NPs of transition metal (e.g., Co, Ni, Cu, Fe) oxides for LIB applications by using 2 µm cobalt oxide (CoO) particles, achieving an electrochemical capacity of 700 mAh·g−1 with 100% capacity retention for up to 100 cycles [26]. For metal oxide in LIB applications, volume expansion occurs during the Li

• reaction medium due to the presence of the magnetic Fe2O3 NPs. In addition, the materials could be regenerated and utilised via a simple annealing treatment. Cobalt oxide (CoO, Co2O3, Co3O4)–graphene hybrids Cobaltosic oxide (Co3O4)–graphene hybrids can be synthesised by solution methods. Like other hybrid

• used for enzymeless glucose detection [191] and determination of carbofuran and carbaryl in fruits and vegetables [192]. Instead of using cobalt oxide–graphene hybrids, Yao et al. have synthesised a cobalt hydroxide nanoflake–rGO hybrid by a one-pot hydrothermal method using glucose as a reducing agent

Methods for preparing polymer-decorated single exchange-biased magnetic nanoparticles for application in flexible polymer-based films

• Laurence Ourry,
• Delphine Toulemon,
• Souad Ammar and
• Fayna Mammeri

Beilstein J. Nanotechnol. 2017, 8, 408–417, doi:10.3762/bjnano.8.43

• applications. Phosphates and phosphonates are suitable for functionalizing iron and silicon oxide surfaces [29][30] through covalent bonds, in mono-, bi- or tridentate modes; but to date, they have not been used for cobalt oxide and ferrite surfaces. In the case of PMMA, we followed two routes: the first one

Thickness dependence of the triplet spin-valve effect in superconductor–ferromagnet–ferromagnet heterostructures

• Daniel Lenk,
• Vladimir I. Zdravkov,
• Jan-Michael Kehrle,
• Günter Obermeier,
• Aladin Ullrich,
• Roman Morari,
• Hans-Albrecht Krug von Nidda,
• Claus Müller,
• Mikhail Yu. Kupriyanov,
• Anatolie S. Sidorenko,
• Siegfried Horn,
• Rafael G. Deminov,
• Lenar R. Tagirov and
• Reinhard Tidecks

Beilstein J. Nanotechnol. 2016, 7, 957–969, doi:10.3762/bjnano.7.88

• layer was sputtered from the same target as the metallic Co layer, however, oxygen gas was mixed into the chamber atmosphere to achieve reactive growth of cobalt oxide. For more details on the sputtering procedures see [8][9][41]. The heterostructure obtained was then cut perpendicular to the thickness

Paramagnetism of cobalt-doped ZnO nanoparticles obtained by microwave solvothermal synthesis

• Jacek Wojnarowicz,
• Sylwia Kusnieruk,
• Tadeusz Chudoba,
• Stanislaw Gierlotka,
• Witold Lojkowski,
• Wojciech Knoff,
• Malgorzata I. Lukasiewicz,
• Bartlomiej S. Witkowski,
• Anna Wolska,
• Marcin T. Klepka,
• Tomasz Story and
• Marek Godlewski

Beilstein J. Nanotechnol. 2015, 6, 1957–1969, doi:10.3762/bjnano.6.200

• synthetic air are presented in Figure 6, Figure 7 and Figure 8, respectively. For the materials which were not annealed, the XRD patterns show a single phase tendency of the samples with a hexagonal wurtzite structure. Peaks associated with cobalt oxide or cobalt hydroxide phases such as CoO, Co2O3 or Co(OH

The role of low-energy electrons in focused electron beam induced deposition: four case studies of representative precursors

• Rachel M. Thorman,
• Ragesh Kumar T. P.,
• D. Howard Fairbrother and
• Oddur Ingólfsson

Beilstein J. Nanotechnol. 2015, 6, 1904–1926, doi:10.3762/bjnano.6.194

Magnetic properties of iron cluster/chromium matrix nanocomposites

• Arne Fischer,
• Robert Kruk,
• Di Wang and
• Horst Hahn

Beilstein J. Nanotechnol. 2015, 6, 1158–1163, doi:10.3762/bjnano.6.117

• , and is usually accompanied by an increase of coercivity (Hc) and of the blocking temperature (TB). The EB was first described by Meiklejohn and Bean in 1956 [4]. They investigated clusters with a FM cobalt core and an AFM cobalt oxide (CoO) shell and consequently observed the characteristic horizontal

Synthesis and electrochemical performance of Li₂Co_1−xM_xPO₄F (M = Fe, Mn) cathode materials

• Nellie R. Khasanova,
• Oleg A. Drozhzhin,
• Stanislav S. Fedotov,
• Darya A. Storozhilova,
• Rodion V. Panin and
• Evgeny V. Antipov

Beilstein J. Nanotechnol. 2013, 4, 860–867, doi:10.3762/bjnano.4.97

• decrease of the olivine impurities and in an increase of the fluorophosphate constituent. The formation of the almost pure Li2Co0.7Fe0.3PO4F was observed upon heating at 740–750 °С. Above these temperatures (>760 °С) samples melted and were heavily contaminated by cobalt oxide. Thus, the annealing at 750